FOXBORO IPM06A CM902WX Pulse input card

Remove the filler panel(s) from the appropriate card slot(s) at the rear of the chassis (if the chassis has a rear card cage). Other modules in the unit may have to be moved to allow space for the cables connected to the LCP2 adapter and the MVME712x family module.An MVME1xx VMEmodule can be connected through the LCP2 adapter to internal SCSI devices as shown in Figure 2-7. This section describes the procedure for connecting the MVME712x modules for use with internal SCSI devices. Because the MVME1xx VMEmodule is at one end of the cable, SCSI terminators are required on the LCP2 adapter. The LCP2 adapter module is shipped with SCSI terminators installed. Note MVME712-13 and MVME712AM: perform the steps in this procedure to connect to internal SCSI devices or the steps in the next section to connect the modem or the steps in both procedures.

Installing for Use with Internal SCSI Devices

Verify that SCSI terminators are installed on the LCP2 adapter module. 2. Install the LCP2 adapter module to the backplane directly in line with the P2 connector on the MVME1xx VMEmodule. Be sure to orient pin 1 of the adapter with pin 1 of the backplane connector. 3. Connect a user-supplied cable with compatible pinouts from connector J3 on the LCP2 adapter to the internal SCSI devices. 4. Verify that terminators are installed on the last SCSI device on the cable. If they are not present, install terminators. 5. MVME712-12 and MVME712-13: Attach the cable supplied with the MVME712x module from LCP2 adapter connector J2 to connector P2 on the MVME712x module. Be sure to orient cable pin 1 with connector pin 1.6. Insert the transition module into the selected slot and tighten the attaching screws. 7. After making sure you will not pinch cables with the cover, reinstall the cover you previously removed.

Check the fuse on the LCP2 adapter module and replace it

if necessary. The fuse on the LCP2 adapter module is for SCSI terminator power. The fuse on the MVME1xx VMEmodule is for Ethernet transceiver power. The resistance of each fuse should be less than 1 Ohm.Install the LCP2 adapter module to the backplane directly in line with the P2 connector on the MVME1xx VMEmodule. Be sure to orient pin 1 of the adapter with pin 1 of the backplane connector. 2. Verify that serial port 2 is configured as a modem port (refer to the Serial Port 2 Configuration paragraph). 3. MVME712-13: Attach the cable supplied with the MVME712-13 module from LCP2 adapter connector J2 to connector P2 on the MVME712-13 module. Be sure to orient cable pin 1 with connector pin 1.

product application

Products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, mechanical, electronic manufacturing, automobile manufacturing, plastic machinery, electric power, water conservancy, water treatment/environmental protection, boiler heating, energy, power transmission and distribution and so on

Superior products

--ABB Accuray

--ABB Advant OCS

--ABB Advant-800xA

--ABB H&B Contrans T

--ABB H&B Freelance 2000

--Allen Bradley PLC

--GE Ran card machine accessories,PLC

--ICS Triplex Rockwell T8151B/T8461/T8310

--Triconex/Foxboro:3625/3721/3503E/FBM237/FBM242

--Emerson:CE3008/VE3008/SE3008/A6120/A6312

--Motorola:MCP750/MVME162/MVME2604/MVME5100

--Woodward:9907-164/9907-167/9905-144/9905-018

The company is mainly engaged in above brands. You are welcome to inquire from me via email!