The MTL5053 has been specifically developed to extend 31.25kbit/s (H1) fieldbus networks into hazardous areas. It provides power and communication to devices powered through the signal conductors. For installations in which the safe-area bus length is small an internal terminator can be enabled by a switch on top of the module. The MTL5053 complies with requirements of Fieldbus Foundation™ specified power supply Type 133† (IS power supply). SPECIFICATION See also common specification Location of fieldbus device(s) Zone 0, IIC, T4–6 hazardous area if suitably certified Hazardous-area fieldbus power supply 18.4V ± 2% 105Ω ±3% dc impedance 80mA maximum current
Maximum cable length
Determined by IS requirements, depending on other devices attached and maximum acceptable voltage drop along cable Digital signal transmission Compatible with 31.25kbit/s fieldbus systems and complies with fieldbus standards† Supply voltage 20 to 35Vdc LED indicator Green: one provided for power indication Power requirement, Vs, with 80mA output load 135mA typical at 24V 105mA at 35V Power dissipation within unit, with 80mA output load 2.3W typical at 24V 2.6W maximum at 35V
To assist the process of terminating cable screens, screw terminals have been provided in terminals 3, 6, 7 and 10. Please note, however, that there is no internal connection for these terminals so they are not earthed.
Note:
To allow adequate heat dissipation under all likely thermal conditions, it is recommended that MTL5053’s are installed on a horizontal DIN-rail mounted on a vertical surface* with a 10mm space between adjacent units. MTL MS010 10mm DIN-rail module spacers are available for this purpose. * If an MTL5053 is mounted in a non-optimum orientation, the maximum operating temperature is reduced to 45°C.
The applicable fieldbus specifications and standards are: Foundation fieldbus™ 31.25kbit/s Physical Layer Profile Specification, document FF-816, IEC 61158-2: 1993 and ISA-S50.02-1992 for 31.25kbit/s fieldbus systems
Company introduction
Temporal Ming sheng automation equipment co., LTD. Was established in April 02, 2021, registered jiujiang ruichang city in jiangxi province, east yi road no. 23 lake farmers 401 mall, the legal representative person Zhou Zuochen.
[Main Products]
Main products: PLC and DCS system spare parts modules of world famous brands
①Allen-Bradley 1756、1746、1747、1771、1785
②Schneider 140 Series PLC module
③General electric GE
IC693 IC697 IC698 Series PLC module
DS200 DS3800 DS215 IS200 IS215 IS220 Series gas turbine module
VMIVME Control module of series
④Bently:3500 series cards 3500/22M、3500/15、3500/92 And other products
⑤ICS TRIPLEX
⑥ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN Robots。
⑦EMERSON:Spare parts for OVATION system, WDPF system and MAX1000 system.
⑧ Invensys Foxboro: I/A Series system, FBM (field input/output module) sequential control, ladder logic control, accident recall processing, digital analog conversion, input/output signal processing, data communication and processing, etc. Invensys Triconex: redundant fault-tolerant control system, Zui modern fault-tolerant controller based on triple module redundancy (TMR) structure.
⑨Woodward:505 series governor 9907-164 And other products
⑩Bosch Rexroth:Indramat,I/O module,PLC CPU,Motors, drives and other products.
◆Motorola:MVME 162、MVME 167、MVME1772、MVME177and other products.