ABB 5SHY35L4510 3BHE014105R0001 IGCT card

Estimated Assembly Time: Approximately 10 minutes. Required Tools: Phillips Screwdriver (not included) 1. Open the grill lid and remove the side shelf from the fire box. 2. The screws used to attach the side shelf are already screwed into the side panels of the grill cart. Remove the screws from the side panels. 3. Align the holes of the left side shelf with the holes in the grill cart. Insert the screws and tighten. NOTE: The top two screws insert from inside the fire box while the bottom two screws insert from under the left side shelf

Secure the top two screws from inside the fire box and the bottom two screws from below the side shelf.

Secure bottom screw from below the side shelf front panel and side burner control panel.

SIDE BURNER ASSEMBLY

 1 Open the grill lid.

 2. The screws used to attach the side burner are already screwed into the right side of the grill cart. Remove the screws from the side panel. 

3. Align the holes on the right side burner with the holes in the grill cart. Insert the screws and tighten. 

4. Align the side burner holes, and tighten all four screws from underneath the side burner

SIDE BURNER HOSE QUICK-CONNECT

 Estimated Assembly Time: Approximately 5-7 minutes Required Tools: Phillips Screwdriver 1. Insert the side burner hose with female sleeve through side panel of cart (Top drawing). 2. Push the sleeve of the female socket back and insert the male end of connector. Release the sleeve. 3. Push the male end into the socket until the sleeve snaps forward to lock the plug in place. 4. To disconnect, push the sleeve back and pull the female end off (bottom drawing).

WARNING 1. Insert the coupling half (socket) into the gas supply line in accordance with ANSI Z223.1/NFPA 54 FUEL gas code. 2. Prior to inserting the plug, test the connection for leaks using the leak test instructions on page 11. After the leak test, rinse the connection with clean water to remove any corrosive residue. 3. Do not use an open flame to test for leaks.

Company introduction

Temporal Ming sheng automation equipment co., LTD. Was established in April 02, 2021, registered jiujiang ruichang city in jiangxi province, east yi road no. 23 lake farmers 401 mall, the legal representative person Zhou Zuochen.

[Main Products]

Main products: PLC and DCS system spare parts modules of world famous brands

①Allen-Bradley 1756、1746、1747、1771、1785

②Schneider 140 Series PLC module

③General electric GE

IC693 IC697 IC698 Series PLC module

DS200 DS3800 DS215 IS200 IS215 IS220 Series gas turbine module

VMIVME Control module of series

④Bently：3500 series cards 3500/22M、3500/15、3500/92 And other products

⑤ICS TRIPLEX

⑥ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN Robots。

⑦EMERSON：Spare parts for OVATION system, WDPF system and MAX1000 system.

⑧ Invensys Foxboro: I/A Series system, FBM (field input/output module) sequential control, ladder logic control, accident recall processing, digital analog conversion, input/output signal processing, data communication and processing, etc. Invensys Triconex: redundant fault-tolerant control system, Zui modern fault-tolerant controller based on triple module redundancy (TMR) structure.

⑨Woodward：505 series governor 9907-164 And other products

⑩Bosch Rexroth：Indramat，I/O module,PLC CPU,Motors, drives and other products. 

◆Motorola：MVME 162、MVME 167、MVME1772、MVME177and other products.