Home > Product > DCS control system > ABB AI820 3BSE008544R1 module

  • ABB AI820 3BSE008544R1 module
ABB AI820 3BSE008544R1 module

ABB AI820 3BSE008544R1 module

ABB AI820 3BSE008544R1 module

Estimated Assembly Time: Approximately 5-7 minutes Required Tools: Phillips Screwdriver (not included) 1. Remove the four side shelf handle screws from the side shelf. 

2. Align the holes in the handle with the holes in the side shelf. 

3. Insert the screws and tighten.

Remove the ignition button housing by turning counterclockwise. 2. Insert the battery into the housing with the positive (+) terminal facing outward. 3. Replace the ignition button housing after the battery has been installed.Connect the PVC Natural Gas Hose to the house gas supply line using the quick-connect fitting as shown in figure A. Check all gas supply fittings for leaks before each use.Do not use the grill until all connections have been checked and do not leak.

LEAK TESTING 

GENERAL Although gas connections on the grill are leak tested prior to shipment, a complete gas tightness check must be performed at the installation site. Before each use check the whole system for leaks following the procedures listed below. If the smell of gas is detected at anytime, you should immediately check the entire system for leaks. BEFORE TESTING Make sure all packing materials have been removed from the grill, including the burner tiedown straps.Make a soap solution of one part liquid detergent and one part water. You will need a spray bottle, brush, or rag to apply the solution to the fittings.

GAS HOOK-UP

 Only the pressure regulator and hose assembly supplied with the grill should be used. Any replacement pressure regulator and hose assembly must be specified by the grill manufacturer. Total gas consumption (per hour) of the 730-0337 Natural gas grill with all burners set on “HI”:The installation of this appliance must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1 and the National Electrical Code ANSI/NFPA No. 70.

                                           

Company introduction

Temporal Ming sheng automation equipment co., LTD. Was established in April 02, 2021, registered jiujiang ruichang city in jiangxi province, east yi road no. 23 lake farmers 401 mall, the legal representative person Zhou Zuochen.

[Main Products]

Main products: PLC and DCS system spare parts modules of world famous brands

①Allen-Bradley 17561746174717711785

②Schneider 140 Series PLC module

③General electric GE

IC693 IC697 IC698 Series PLC module

DS200 DS3800 DS215 IS200 IS215 IS220 Series gas turbine module

VMIVME Control module of series

④Bently3500 series cards 3500/22M3500/153500/92 And other products

⑤ICS TRIPLEX

⑥ABB Robots. FANUC RobotsYASKAWA RobotsKUKA RobotsMitsubishi RobotsOTC RobotsPanasonic RobotsMOTOMAN Robots

EMERSONSpare parts for OVATION system, WDPF system and MAX1000 system.

⑧ Invensys Foxboro: I/A Series system, FBM (field input/output module) sequential control, ladder logic control, accident recall processing, digital analog conversion, input/output signal processing, data communication and processing, etc. Invensys Triconex: redundant fault-tolerant control system, Zui modern fault-tolerant controller based on triple module redundancy (TMR) structure.

Woodward505 series governor 9907-164 And other products

⑩Bosch RexrothIndramatI/O module,PLC CPU,Motors, drives and other products. 

◆MotorolaMVME 162MVME 167MVME1772MVME177and other products.

Obtain the latest price of ABB AI820 3BSE008544R1 module