Home > Product > DCS control system > ABB SDCS-COM-1 CPU module

  • ABB SDCS-COM-1 CPU module
ABB SDCS-COM-1 CPU module

ABB SDCS-COM-1 CPU module

ABB SDCS-COM-1 CPU module

TO LIGHT THE SEARING SIDE BURNER: 1. Open the lid. 

2. To ignite the searing side burner, simply press and turn the knob to “IGNITE/HI” setting. There will be a “clicking” sound if the ignition system is working correctly. After ignition, hold in the knob for 15 seconds and release. 

3. If the burner does not light, turn the knob to the “OFF” position. 

4. If the igniter does not function, wait 5 minutes for any excess gas to dissipate, and follow the instructions on page 16 for match lighting

Keep a spray bottle of soapy water near the gas supply valve and check the connections before each use.

MAIN BURNER LIGHTING

Turn the main burner control knobs to the “IGNITE / HI” setting. Push the control knob until the burner ignites; you should hear a “clicking” sound if the electronic ignition system is working properly. The burner should ignite within 4 seconds Once the burner ignites, adjust the temperature level as desired.Push and turn rear burner knob slowly to “IGNITE / ON” setting, hold in until th burner is lit up, continue to press and hold for 15 seconds and release. You should hear a “clicking” sound if the electronic ignition system is working properly.Push and turn searing side burner knob to “IGNITE / HI” setting, hold in until the burner ignites. The burner should ignite within 4 seconds. After ignition, continue to press and hold for 15 seconds and release.

TO MATCH LIGHT THE GRILL

 If the burner will not light after several attempts using the control knobs, the burner may be lit with a match. 1. If you have already attempted to light the burner with the igniter, wait 5 minutes for any accumulated gas to dissipate. 2. Insert a match into the lighting rod. Ignite the match and insert through the cooking grids to the burner. 3. Press and turn the control knob to the “IGNITE/HI” setting. Continue to press the knob until the burner ignites. The burner should light immediately. 4. If the burner does not light within 4 seconds, turn the knob to the “OFF” position. Wait 5 minutes for the gas to dissipate and try again.

                                           

Company introduction

Temporal Ming sheng automation equipment co., LTD. Was established in April 02, 2021, registered jiujiang ruichang city in jiangxi province, east yi road no. 23 lake farmers 401 mall, the legal representative person Zhou Zuochen.

[Main Products]

Main products: PLC and DCS system spare parts modules of world famous brands

①Allen-Bradley 17561746174717711785

②Schneider 140 Series PLC module

③General electric GE

IC693 IC697 IC698 Series PLC module

DS200 DS3800 DS215 IS200 IS215 IS220 Series gas turbine module

VMIVME Control module of series

④Bently3500 series cards 3500/22M3500/153500/92 And other products

⑤ICS TRIPLEX

⑥ABB Robots. FANUC RobotsYASKAWA RobotsKUKA RobotsMitsubishi RobotsOTC RobotsPanasonic RobotsMOTOMAN Robots

EMERSONSpare parts for OVATION system, WDPF system and MAX1000 system.

⑧ Invensys Foxboro: I/A Series system, FBM (field input/output module) sequential control, ladder logic control, accident recall processing, digital analog conversion, input/output signal processing, data communication and processing, etc. Invensys Triconex: redundant fault-tolerant control system, Zui modern fault-tolerant controller based on triple module redundancy (TMR) structure.

Woodward505 series governor 9907-164 And other products

⑩Bosch RexrothIndramatI/O module,PLC CPU,Motors, drives and other products. 

◆MotorolaMVME 162MVME 167MVME1772MVME177and other products.

Obtain the latest price of ABB SDCS-COM-1 CPU module