The main products

Spare parts spare parts, the DCS control system of PLC system and the robot system spare parts,

Brand advantage: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts

Products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, machinery, electronics, automobile manufacturing, tobacco, plastics machinery, electric power, water conservancy, water treatment/environmental protection, municipal engineering, boiler heating, energy, power transmission and distribution and so on.

140CHS11000 Output module

PerkinElmer recommends that BSA and detergents exceeding 0.05 mg/mL and 0.01% (v/v) respectively in concentration not be used. Higher concentrations can result in chip failure. In addition, non-aqueous solvents are not compatible with DNA LabChip protocols Particulates All sample plates should be spun down prior to analysis. All buffers should be filtered with a 0.22 µm cellulose acetate filter. Salt Concentration Total salt concentration must not exceed 125 mM. Plasmids Plasmid concentration in samples must be below 20 ng/µL. Please note that although the DNA Assays cannot analyze plasmids, the presence of plasmids above 20 ng/µL can interfere with assay results

We recommend that this product and components be handled only by those who have been trained in laboratory techniques and that it is used in accordance with the principles of good laboratory practice. As all chemicals should be considered as potentially hazardous, it is advisable when handling chemical reagents to wear suitable protective clothing, such as laboratory overalls, safety glasses, and gloves. Care should be taken to avoid contact with skin or eyes. In case of contact with skin or eyes, wash immediately with water

Kit Contents Storage: 

When not in use, store chips and reagents refrigerated at 2 - 8°C until next use. If using the chip again within 24 hours it may be left at room temperature. Allowing the chip wells to dry may lead to changes in chip performance. DNA 1K Reagent Kit Part Number CLS760673 Each kit contains enough reagents for 20 Low-throughput (LT) or 10 High-throughput (HT) chip preparations. Up to 48 samples can be tested with a LT chip preparation. Up to 384 samples can be tested with a HT chip preparation.

Preparing the Gel-Dye Solution

 Notes: The Dye Concentrate contains DMSO and must be thawed completely before use. One vial of DNA Gel Matrix (red cap ) is good for 4 Lowthroughput chip preparations or 2 High-throughput chip preparations. Up to 48 samples can be tested with a LT chip preparation. Up to 384 samples can be tested with a HT chip preparation. 1 Vortex the thawed DNA Dye Concentrate (blue cap ) for 10- 15 seconds before use. 2 Transfer 13 µL of DNA Dye Concentrate (blue cap ) to 1 vial of DNA Gel Matrix (red cap ). 3 Vortex the solution until it is well mixed and spin down for a few seconds. 4 Transfer the mixture into two spin filters (approximately 550 µL each). 5 Centrifuge at 9200 rcf for 7.5 minutes at room temperature. 6 Discard filters, label and date the tubes. 7 Store in the dark at 2 - 8°C. Use within 3 weeks.

Additional Items Required 

• 18 megohm, 0.22-µm filtered water (Milli-Q® or equivalent). • 70% isopropanol solution in DI water. • Bio-Rad Hard-Shell® 384-well Skirted PCR Plates, Cat. # HSP38XX (recommended) • PerkinElmer Hard-Shell thin-wall 96-well skirted PCR plate (blue), Cat. # 6008870 (recommended) Note: Allow the chip and reagents to equilibrate to room temperature for at least 30 minutes before use.