The main products

Spare parts spare parts, the DCS control system of PLC system and the robot system spare parts,

Brand advantage: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts

Products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, machinery, electronics, automobile manufacturing, tobacco, plastics machinery, electric power, water conservancy, water treatment/environmental protection, municipal engineering, boiler heating, energy, power transmission and distribution and so on.

HONEYWELL CC-PAIX02 Actuator module

The cable 07 SK 92 is used to connect a 9–pole serial interface connector of CS31 compact PLCs or T200 communication processors with a modem with a standard interface (see 13.8.1 Survey table). If another modem has to be connected, the cable must be modified possibly. Mechanical Design Plug 1 SUB–D plug, 9–pole male, on the side of 07 KP 6x, 07 KR 91, 07 KT 92. The housing is metal–plated, the shield is connected to the metal plate. Plug 2 SUB–D plug, 25–pole male, on the side of the modem. The plugs are mounted to both interfaces by means of screws.

The shown cable can be used to connect a 9–pole serial interface connector of CS31 compact PLCs or T200 communication processors with the 07 DR 12 printer (EPSON FX 870, serial interface C823061) (see 13.8.1 Survey table). If another printer has to be connected, the cable must be modified possibly. Mechanical Design Plug 1 SUB–D plug, 9–pole male, on the side of 07 KP 6x, 07 KR 91, 07 KT 92. The housing is metal–plated, the shield is connected to the metal plate. Plug 2 SUB–D plug, 25–pole male, on the side of the printer. The plugs are mounted to both interfaces by means of screws.

Lithium Battery Module 07 LE 90 R1 

for data back-up in processor units of ABB Procontic systems The 07 LE 90 R1 lithium battery module is used for RAM data back-up in several processor units of ABB Procontic programmable control systems. In order to change the battery quickly, it is equipped with a 2–pole plug and two soldered wires. The following handling advice has to be taken into due consideration:
Use only genuine ABB lithium battery modules.
Replace battery before it is fully exhausted.
Do not short–circuit battery! It may cause overheating or explosion. Prevent accidental short–circuit. Therefore, do not put battery into metallic boxes or on metallic surfaces.
Do not try to charge battery! It may cause overheating or explosion.
Replace battery only during the power is on. Otherwise you can lose data.
Dispose of the battery ecologically!
Pay attention to the battery monitoring facilities on the devices, e.g., LED indications, whether the battery is exhausted or missing. The battery lifetime depends on the unit where it is installed.

Battery Lifetime 

The value of the battery lifetime says how long the battery is able to back-up the stored data while the unit is not supplied by the internal voltages. If the internal voltages are switched on, the battery is only discharged by its own leakage current. Type of unit, where the battery is installed Battery lifetime t (guaranteed values @ 25 °C)Technical Data Capacity 1000 mAh Storage temperature – 10 _C...+ 75 °C Operating temperature 0 _C...+ 55 °C No–load voltage 3.6 V Rated voltage 3.5 V Temperature coefficient of rated voltage ca. –1 mV/K Temperature coefficient of capacity < –1,5 % @ 0...70 °C Self discharge

• DC drives (e.g. DCS 600 products) use 10 MBd optical transmitters/receivers. • ACS 600 products use 5 MBd as well as 10 MBd optical transmitters/receivers. • Mechanically both types are identical i.e accept the same cable connectors. • Mixing 5 MBd and 10 MBd is not possible. • With 5 MBd optical components only plastic optical fibre cable (POF) can be used.