The main products

Spare parts spare parts, the DCS control system of PLC system and the robot system spare parts,

Brand advantage: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts

Products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, machinery, electronics, automobile manufacturing, tobacco, plastics machinery, electric power, water conservancy, water treatment/environmental protection, municipal engineering, boiler heating, energy, power transmission and distribution and so on.

A4H254-8F8T P0973JP switches

▪ An embedded Ethernet interface provides:  Data exchange using Ethernet Global Data (EGD)  TCP/IP communication services using SRTP  Support for SRTP Channels, Modbus/TCP Server and Modbus/TCP Client  Full programming and configuration services  Comprehensive station management and diagnostic tools  Two full-duplex 10BaseT/100BaseT/TX (RJ-45 Connector) ports with an internal network switch providing auto-negotiated network speed, duplex mode, and crossover detection.  Time synchronization to SNTP timeserver on Ethernet network (when used with Release 5.00 or later CPU module).

During normal operation, the primary and secondary units in an HSB redundancy system must have the same CPU model type. Extended operation with dissimilar CPU types is not allowed. The primary and secondary units with dissimilar CPU model types can be synchronized for a limited time, for the purpose of system upgrade only. Fail wait times for the higher performance CPU in a dissimilar redundant pair may need to be increased to allow synchronization. Either model can be in the primary or secondary unit.

Important Product Information for this Release

 Ethernet Firmware version 6.20 adds support in SNTP for local time zones and daylight savings. For details, see “New Ethernet Features and Enhancements in Firmware Version 6.20” on page 5. For problems resolved in this release, see “Ethernet Problems Resolved in Firmware Version 6.20” on page 18. Hardware version -Hx corrects the hardware ID to enable low battery detection when used with a smart battery. Important Note: It is recommended that the user change the station manager password to a password other than the default password. Access to remote station manager will be disabled when the station manager password is set to the default password. GE Intelligent Platforms recommends disabling FTP server and/or Web server connections if not used. For details, see page 22

The C Toolkit for PACSystems is distributed with Proficy Machine Edition Logic Developer. Updates can be downloaded from http://www.ge-ip.com/support. C Toolkit Release 5.50 or later is required for LREAL data type support. C Toolkit Release 5.00 Build 16C1 or later is required when the PACSystems CPU contains firmware Release 5.00 or later. Notes: C blocks that were built using C Toolkit versions earlier than 5.00 Build 16C1 must be recompiled using a newer toolkit version for use with CPU firmware release 5.00 or higher. The Series 90 Toolkit (IC641SWP709/719) is not compatible with PACSystems.

CPU might not detect low-battery condition

Unless a smart battery is in use, PACSystems CPUs may not detect a low-battery condition early enough to provide a meaningful warning to replace the battery. A legacy battery with very low capacity may still have a terminal voltage high enough to report that it is a good battery. In this case, when the battery starts supplying the memory power (battery backup), the battery voltage would quickly drop to unacceptable levels, with little warning to the user before failure. To insure against data loss when using any type of battery other than a smart battery, users should replace batteries in accordance with the guidelines provided in the PACSystems Controller Battery and Energy Pack Manual, GFK-2741. Additionally, users could save logic and hardware configuration to flash.

If the Ethernet connection is broken during a word-for-word change, the programmer may not allow a subsequent word-for-word change after reconnecting due to the fact that it thinks another programmer is currently attached. If this occurs, you should go offline and then back online again.