The main products

Spare parts spare parts, the DCS control system of PLC system and the robot system spare parts,

Brand advantage: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts

Products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, machinery, electronics, automobile manufacturing, tobacco, plastics machinery, electric power, water conservancy, water treatment/environmental protection, municipal engineering, boiler heating, energy, power transmission and distribution and so on.

ALSTOM PIB310 3BHB0190 Control card

The following procedure describes how to edit setpoint files. 1. Run the 369PC software. It is not necessary to have a 369 relay connected to the computer. If 369PC is not communicating with the relay, the status bar will indicate that the program is in “Editing File” mode and “Not Communicating”. 2. If the 369PC program is communicating, select the Communication > Computer menu item to launch the COMMUNICATION/COMPUTER window (see Figure 4–2: COMMUNICATION / COMPUTER WINDOW on page 4–4) and set Communicate to Off. Click OK to turn off communications to the relay and place 369PC in “Editing File” mode. 3. Open a setpoint file by selecting the File > Open menu item. Locate the appropriate 369 setpoint files (ending with the extension 369) and select OK. Note that 369PC can open both 369 and 269 setpoint files. For instructions on using 269 setpoint files with the 369, see Section 4.2.10: CONVERTING 269 SETPOINT FILES TO 369 on page 4–8. 4. From the Setpoints menu item, choose the appropriate setpoints section to program; for example, System Setup > Output Relay Setup to edit the output relay setup setpoints. When you have finished editing a page, select OK to store the information to the PC’s scratchpad memory (NOTE: this action does store the information as a file on a disk). 5. Repeat Step 4 until all the desired setpoints are edited. Select the File > Save As menu item to store this file to disk. Enter the location and file name of the setpoint file with a file extension of ‘.369’. 6. The file is now saved to disk. See Section 4.2.8: DOWNLOADING A SETPOINT FILE TO THE 369 on page 4–6 for instructions on downloading this file to the 369.

DOWNLOADING A SETPOINT FILE TO THE 369 

The following procedure describes how to download setpoint files to the 369. 1. To download a pre-programmed setpoint file to the 369, run 369PC and establish communications with the connected relay via the faceplate RS232 port or through the RS485 connector. 2. Select the File > Open menu item to locate the setpoint file to be loaded into the relay. Click OK to load. 3. When the file is completely loaded, the 369PC software will break communications with the connected relay and the status bar changes to indicate “Editing File”, “Not Communicating”. 4. Select the File > Send Info To Relay menu item to download the setpoint file to the connected relay. 5. When the file is completely downloaded, the status bar will revert back to “Communicating”. The relay now contains all the setpoints as programmed in the setpoint file. If an attempt is made to download a setpoint file with a revision number that does not match the relay firmware revision, the following message type will appear: See Section 4.2.9: UPGRADING SETPOINT FILE TO NEW REVISION on page 4–7 for instructions on upgrading the setpoint file.

UPGRADING SETPOINT FILE TO NEW REVISION

 The following procedure describes how to upgrade setpoint file revisions. It may be necessary to upgrade the revision code for a previously saved setpoint file when the 369 firmware is upgraded. 1. To upgrade the revision of a previously saved setpoint file, run the 369PC software and establish communications with the 369 through the front RS232 port or through the RS485 connector. 2. Select the Actual > A6 Relay Information menu item and record the Main Software revision number (for example, 53CMB130.000, where 130 is the main revision identifier and refers to firmware version 1.30).3. Select the File > Open menu item and select the setpoint file to be downloaded to the connected relay. When the file is open, the 369PC software will be in “File Editing” mode and “Not Communicating”. 4. Select the File > Properties menu item and note the version code of the setpoint file.5. If the Version code (e.g. 1.4X above) differs the firmware revision (noted in step 2 as 130), select the revision code that matches the firmware from the pull-down tab. For example: for firmware revision 53CMB170.000 and current setpoint revision as 1.61; change the Version code to 1.7X to upgrade. 369 firmware versions 1.10 and 1.12 are not compatible with newer versions. A new setpoint file must be created! 6. Select the File > Save menu item to save the setpoint file. 7. To download the upgraded setpoint file to the 369, see Section 4.2.8: DOWNLOADING A SETPOINT FILE TO THE 369 on page 4–6