The main products

Spare parts spare parts, the DCS control system of PLC system and the robot system spare parts,

Brand advantage: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts

Products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, machinery, electronics, automobile manufacturing, tobacco, plastics machinery, electric power, water conservancy, water treatment/environmental protection, municipal engineering, boiler heating, energy, power transmission and distribution and so on.

Honeywell CC-IP0101 51410056-175 module

Digital control units in 1–axis and 2–axis versions (for 1PH, 2–axis control is only possible with High Performance) are available to operate motors 1FT6/1FK/1FN1/1FN3/1FE1/1PH/1PM/1FM6/2SP1. During the initialization phase (power on or reset), the drive software is downloaded from the SINUMERIK 840D to the control board via the drive bus. High Performance: Order No.: 6SN1118–0DJ2–0AA The digital 1–axis High Performance control can be loaded with the drive software for either FD control or MSD control. MSD and FD have the same user interface. The board is available in the following versions: Basic version with sinusoidal voltage signals and the possibility of connecting absolute encoders with EnDat interface In addition, the evaluation of a direct position measuring system with sinusoidal voltage signals and the connection of absolute encoders with EnDat interface and SSI interface (as of SW 5.1.9) is possible. The module is available in three basic versions that differ in the controller performance and in the evaluation of the direct position measuring systems: High Performance: Order No.: 6SN1118–0DK2–0AA Basic version with sinusoidal voltage signals and the possibility of connecting absolute encoders with EnDat interface In addition, the evaluation of two direct measuring systems with sinusoidal voltage signals and the connection of absolute encoders with EnDat interface and SSI interface (as of SW 5.1.9) is possible.

High Standard: Order No.

 6SN1118–0DM3–0AA Basic version with sinusoidal voltage signals and the possibility of connecting absolute encoders with EnDat interface. Additionally with evaluation for 2 direct measuring systems with sinusoidal voltage signals and the possibility of connecting absolute encoders with EnDat interface and SSI interface (from SW 5.1.9). Note A 2–axis drive control can also be operated in a single axis power module for single axis applications. It is engineered as a 1–axis board. For motor encoders without any adjustment to the EMF of the synchronous motor (1FE1/1FN1/1FN3) a configurable, automatic identification technique can be used to determine the electrical rotor position. In so doing, motion of typically <5 degrees mechanical is not exceeded. The identification routine is performed after each power up operation.When using non–PELV circuits at terminals AS1, AS2, connectors must be coded to prevent the connectors being incorrectly inserted (refer to EN60204–1, Section 6.4). For Order No. for coded connectors, refer to Catalog NC 60.

SIMODRIVE 611 universal HRS” control board

The ”SIMODRIVE 611 universal HRS” control board is used in the SIMODRIVE 611 system (SW 8.3) and includes two drive controls that are independent of one another. However, the board can also be used for 1–axis applications and in 1–axis power modules. Note The control board is described in detail in: References: /FBU/ Description of Functions, SIMODRIVE 611 universal The functionality specified in this Description of Functions under ”SIMODRIVE 611 universal” also applies to ”SIMODRIVE 611 universal HR”.Settings All drive–related settings of the control board can be made as follows: – Using the SimoCom U parameterizing and startup tool on an external PG/PC – Using the display and operator control unit on the front panel – Using PROFIBUS DP (parameter area, PKW area) Software and data The firmware and the user data are saved on a memory module which can be replaced. The software designation on the memory module refers to the system software including the initial program loader. Terminals and operator control elements – 2 analog inputs, 2 analog outputs per drive – 4 digital inputs, 4 digital outputs per drive – 2 measuring sockets – POWER–ON RESET pushbutton with LED – Display and operator unit